DSR 2019 build

Well, a new heating season is begun and with it a new iteration of the previous Rocket stove, called a Double Shoebox Rocket.

The group over at the Donkey forum did some experimentation back in 2018 coming up with this concept, which was later abandoned by Peter van den Berg, the chief experimenter on the project, as being too unreliable.

By the time he had moved on to a different design I had already started building, it was getting colder, and looking at the elements that seemed to make the DSR run away with the burn, they did not seem as relevant to my design, so I just continued to build according to his best guess dimensions.

My 2018 build used a number of walls that were simply formed of clay, or a clay perlite mix, and a couple of the sides around the water tank were taken from an old washing machine, with some fiberglass insulation hastily fastened to the inside of the walls, with clay slopped around the top and edges to give a seal.

The door to the burn chamber, as in many projects done on the cheap was a problem until I finally bought a couple pieces of neoceram stove glass, which cost more than all the previous stoves from the last several years.

While this new glass has proved very durable, having a door that really is robust requires more than just a glass pane, so that is still in the development phase, although I’m pretty sure I have a workable solution which will likely happen sometime during this season. For now I continue to get a potholder if the glass is hot, and as gently as possible remove it and then wedge it back into place.

The other main change is the use of bricks to give a substantial continuous exterior that is well sealed and even looks a little better.

One other important note, my exhaust was set up for a low temperature ground level “stack” and to use the push of the j tube rather than the pull of a draft. Since the first batch box conversion about three years I found it necessary to install a fan at the end of the exhaust pipe to aid with the draft. This totally eliminates smoke at start up and keeps the draft more even.

while it may appear the smoke is being pumped into the ground, the downward tube is actually wide open at the seam, this arrangement helps prevent sudden gusts from totally disrupting the draft
The brick exterior is continuous back to the poured concrete wall as I continue to remove clay from the previous construction. the removed clay goes right back into the new build
note the wet perlite clay mixture formed in place around the DSR core. The stack/exhaust is on the floor at the right side of the shovel
the clay perlite insulation layer continues across the concrete wall in back
The second chamber is now well defined and the brick courses are starting to grow
Note the rectangular passage on the right where the exhaust comes in to the first bell from the secondary burn chamber. The rim of the duct to the water tank “bell” can be seen just opposite this entrance and further down in the chamber
The right side of the water tank shows the location of the duct from the first bell just visible above the top of the front bricks
overall layout of stove. note exhaust moves from right to left through the chambers and at the bottom of the water tank chamber it turns back and flows under the construction to the exhaust “stack”
salvaged glass stove tops are sealed with wet clay to the top. Note the left side galvanized pipes exit and the blue pipe insulation for the hot water outlet
proof of concept, the first fire verifies the exhaust, now the drying process begins
looks just like the pictures I saw when I first started last year, note that the bricks are joined with a clay “mortar”, if I want to rebuild, everything is easily recycled with water as the solvent
I usually have a small piece of ceramic fiber board over the glowing section of the stove top. Temperatures are way hot, and after passing 1000 degrees F it just registers as “HI”

cooking can be done here, very carefully, but I like the idea of more insulation to increase efficiency of the burn. The second chamber still has plenty of heat for a more reasonable cooking surface, and even the water tank chamber can keep things warm
with the top cleared and clean

27 thoughts on “DSR 2019 build”

  23. That night, I did a whole spa routine to make sure my skin was soft and my ass was stretched and wet. I was wearing nothing but a jockstrap as I was told. Waiting by the door on fourth. My heartbeat was so fast as my mouth was dry. I heard the footstep approaching. I left the door unlocked as one of the instructions I was received from daddy. He stepped in with his size 10 Christian Loublitine loafer where my eyes were going up from there. When I made eye contact with daddy, daddy slapped me across the face and said, “Bad boy, Where the fuck are your sneakers as I told you to wear tonight.” I was trembling and said in a very low voice, “ sorry daddy I fooooorgot.” dzieciД™ce porno “I knew ya couldn’t keep your hands off it.” His dad says. “Men can’t do it, we are drawn to our cocks, like a moth to a flame, and usually that burning sensation that a man feels is the cum boiling up in our balls. You know that feelin’ doncha son?”

    Reply
  24. ThomasEquag

    The Real Person!

    Author ThomasEquag acts as a real person and passed all tests against spambots. Anti-Spam by CleanTalk.

     says:

    Excellent write-up. I certainly love this website. Thanks!

    koobstore.in

    Reply

Leave a Reply

Your email address will not be published. Required fields are marked *